The Racing Magazine in the Islands
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

wiring car stereo for novices

 
Post new topic   Reply to topic    Zorce.com Forum Index -> AudioZORCE
View previous topic :: View next topic  
Author Message
SaLt ShaKer
Sith-ing down in the corner


Joined: 06 Apr 2005
Posts: 52
Location: AudioZorce

PostPosted: Mon Apr 11, 2005 11:37 am    Post subject: wiring car stereo for novices Reply with quote

How to Wire a Car Stereo System

Preparing for the Installation

Steps:

1. Gather the following tools: knife or wire cutters, solder and solder gun, crimps, stripper, screwdriver, screws.

2. Plan the installation. Know where you intend to put all the components. For example, the radio is commonly put in the factory opening in the dash, the speakers are put in the factory openings in the front doors, and the rear speakers are put in the factory openings on the rear deck. The equalizer goes in the factory opening below the radio in the dash. An amplifier with built-in electronic crossover usually goes in the trunk. The car's battery, which powers the system, is commonly under the hood, usually on the passenger's side of the car.


Routing Power, Ground and Signal Wires

Steps:

1. Route the power cable from the battery through the passenger side of the car to the amplifier in the trunk. This will prove easiest because the battery is commonly on the passenger's side of the car. You will have to feed the power cable through a rubber grommet on the firewall.

2. Route the signal cables (RCA cables) on the driver's side of the car from the head unit to the amplifier.

3. Ground the amplifier to a clean metal surface on the car's chassis. The ground should be no more than 18 inches from the amplifier. The ground cable must be the same gauge size as the power cable being used.


Tips:

You don't want to route signal wire next to power wire because that could result in noise entering the sound system. If power cable and signal cable must cross, cross them perpendicularly.

The gauge of the power cable is determined by the specifications of the amplifier you are using. The owner's manual that comes with the amplifier will probably tell you what gauge cable to use. If it does not, consult with a tech advisor from the manufacturer of the amplifier to find out.

Use well-shielded RCA cable. This will help prevent noise from entering the sound system.


Wiring the Radio and Connecting Components

Steps:

1. Connect the radio to a constant 12-volt source, an ignition lead, the amplifier turn-on and the antenna. On newer cars, the constant 12-volt and the ignition wire connections can be made through the factory wire harness. On older cars, the fuse block can serve as the constant 12-volt source.

2. Ground the radio to the chassis.

3. Connect the antenna to the proper antenna input on the radio.

4. Connect the radio to the amplifier so when you turn on the radio, you are also turning on the amplifier. Most radios have a power antenna output. This is a 12-volt line that runs the power antenna. When the radio is turned on, the power antenna goes up; when the radio is turned off, the power antenna goes down. Use the power antenna lead to also turn on the amplifier. Use a relay to make the connection, so that the line can run both the power antenna and the amplifier turn-on. Ask a neighborhood car audio retail dealer how to connect the relay. Some radios have a separate power antenna output and a separate amplifier output. If this is the case with your radio, use the amplifier output to turn on the amplifier.

5. Begin connecting components using 18-gauge or 16-gauge wire on the speakers. The wires run from each speaker to the amplifier. The longer the run, the more resistance on the wire. The larger the gauge size of the wire, the less resistance.

6. Run the speaker wire on the same side of the car as the signal wire.

7. Connect the speakers in either a parallel or series configuration. A parallel connection is when you connect each speaker's positives together and each speaker's negatives together. A series hook-up is when you connect one speaker's negative to the second speaker's positive.

8. After connecting the speakers together, run the wires to the amplifier and connect the positive wires to the positive inputs of the amplifier and the negative wires to the negative inputs of the amplifier.


Tips:

When wiring speakers together and to the amplifier, you need to consider the impedance, or ohms, rating of the speakers as well as the ohms load of the amplifier. Amplifiers are constructed to "see" a certain ohms load. If the load the amplifier sees falls below what it is capable of handling, the amplifier will shut off. Speakers come with various ohms ratings. When speakers are connected together, the ohms rating, or impedance, of the group of speakers that are wired together changes and affects the ohms load of the amplifier. If you wire two 4-ohm speakers together in a series hook-up, you are producing an ohms load of 8 ohms. If you wire two 8-ohm speakers in parallel, you are creating an ohms load of 4 ohms (8 ohms x 8 ohms divided by 8 ohms + 8 ohms = a 4 ohms load on the amplifier). If you connect two 8-ohm subwoofers in a parallel hook-up to an amplifier that is bridged mono, the amplifier will see half of the load because it is bridged. So it will be seeing a 2 ohms load.

Before you do a parallel hook-up on an amplifier, make sure that the amp can take the ohms load that will result. Find out what ohms load the amplifier is stable at and then choose speakers with the appropriate ohms rating, so that the hook-up will ensure that the ohms load is within the capability of the amplifier.

Generally speaking, most midrange, midbass and tweeters you use will be 4-ohm rated. Most subwoofers you use will be 4- or 8-ohm rated.

If you are using passive crossovers with the component speakers in the front and rear of the car, hooking up these crossovers can also affect the ohms load seen by the amplifier. Hooking up the passive crossovers' positive and negative properly can be a concern. Follow the speaker manufacturer's instructions carefully.

If you are preparing to hook up wires to the amplifier and you are not sure which is negative and which is positive, take a 9-volt battery and tap the speaker wire to the positive terminal of the battery. If the speaker first moves forward (or out), then you have touched the positive lead of the speaker to the positive terminal of the battery, and the remaining wire is negative. If the speaker's first move is backward (or in), you have touched the negative wire of the speaker to the positive terminal of the battery.

Helpful link: http://www.bcae1.com/
_________________


Z i FORI DONDOLA!
Back to top
View user's profile Send private message Visit poster's website AIM Address MSN Messenger
Rick
Pumpum Conqueror


Joined: 26 Jun 2005
Posts: 14

PostPosted: Sun Jun 26, 2005 10:17 pm    Post subject: Reply with quote

Arite im kinda new to this ......so dont laught at me
Heres what.........can i utilise the 4 speaker output wires from my deck AND also use the 2 RCA outs to power my speakers .... would it put extra strain on de deck????
Back to top
View user's profile Send private message
Shazad Rahaman
Official Zorce Sorrel Drinker


Joined: 15 Apr 2005
Posts: 70
Location: Party Now Explain Later

PostPosted: Wed Jun 29, 2005 2:28 pm    Post subject: Reply with quote

i am guessing here you meant
to sue the speaker outputs from the deck to power the speakers and also use the rca signal to feed amplifiers to play more speakers
the answer is yes you can
it will not "strain" the deck
Back to top
View user's profile Send private message MSN Messenger
Computerman
Rebel Speeder


Joined: 10 Jun 2005
Posts: 88
Location: Freeport

PostPosted: Wed Jun 29, 2005 7:37 pm    Post subject: Reply with quote

What about grounding to the negative terminal on the battery? Is this better then just grounding on the chassis?
_________________
Boosted Baby!

http://gatt.carigamers.com
Back to top
View user's profile Send private message Visit poster's website
Rick
Pumpum Conqueror


Joined: 26 Jun 2005
Posts: 14

PostPosted: Thu Jun 30, 2005 10:28 am    Post subject: Reply with quote

Thanks for da info....!
Back to top
View user's profile Send private message
SaLt ShaKer
Sith-ing down in the corner


Joined: 06 Apr 2005
Posts: 52
Location: AudioZorce

PostPosted: Tue Jul 12, 2005 11:34 am    Post subject: Reply with quote

Quote:
What about grounding to the negative terminal on the battery? Is this better then just grounding on the chassis?


grounding on battery terminal isnt advisable as this just adds to charge build up in ur lil closed circuit... what you want is to get rid of these extra charges best route is out on the body of the car chassis,keep your ground wires to your amplifier as short as possible to ensure least resistence in your system,this helps in clarity of your sound reproduction
_________________


Z i FORI DONDOLA!
Back to top
View user's profile Send private message Visit poster's website AIM Address MSN Messenger
Turbodrive
Rebel Zorce Ossifah


Joined: 25 May 2005
Posts: 105
Location: South ah d border

PostPosted: Tue Sep 06, 2005 9:52 am    Post subject: Reply with quote

Good Info Shaker.
_________________
Back to top
View user's profile Send private message Send e-mail Yahoo Messenger MSN Messenger
Master Rolla
Rebel Zorce Ossifah


Joined: 22 Dec 2005
Posts: 102
Location: in the Mill101 Falcon

PostPosted: Sat Aug 12, 2006 9:16 am    Post subject: Reply with quote

good info there
Back to top
View user's profile Send private message
Plex
Zorce Jedi Master


Joined: 01 May 2005
Posts: 9039
Location: T&T

PostPosted: Sat Aug 12, 2006 6:25 pm    Post subject: Reply with quote

cool...
Back to top
View user's profile Send private message Send e-mail Visit poster's website Yahoo Messenger MSN Messenger
MASS DESTRUCTION AUDIO
Pumpum Conqueror


Joined: 10 Feb 2007
Posts: 23
Location: Chaguanas

PostPosted: Sat Feb 17, 2007 5:44 am    Post subject: Reply with quote

i was planning to do that to save wire but was advise not to.
so i used audiopipe 0guage for ground an Stinger hpm i think,d clear one, for power.
ting dam expensive
Back to top
View user's profile Send private message MSN Messenger
Display posts from previous:   
Post new topic   Reply to topic    Zorce.com Forum Index -> AudioZORCE All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group